| Izvorni znanstveni radovi |
|
|
|
| M. Zhou, T. Jiang, S. T. Yang, K. Ma, X. X. Xue, W. J. Zhang – Optimization utilization of vanadium – titanium iron ore in sintering based on orthogonal method (str. 581-584) |
PDF 223 KB |
|
|
| S. T. Yang, M. Zhou, T. Jiang, X. X. Xue, P. N. Duan, W. J. Zhang – Effect of CaO/SiO2 ratio on melting property and strength of sinter with vanadium-titanium iron ore addition (str. 585-588) |
PDF 213 KB |
|
|
| A. Kmita, J. Zych, M. Holtzer, J. Mocek, S. Piasny – Ecological water-based protective coatings for moulds and cores of iron castings (str. 589-592) |
PDF 360 KB |
|
|
| C. J. Xu, Y. X. Zeng, Z. L. Wang, J. Li, S. L. Li, X. J. Zhang – Magnetic field distribution in the electromagnetic feeding riser of rectangle steel ingot (str. 593-596) |
PDF 210 KB |
|
|
| G. W. Ao, M. G. Shen, Z. S. Zang, B. L. Li – Study on unidirectional solidification ingot with hollow lateral wall insulation (str. 597-600) |
PDF 228 KB |
|
|
| M. G. Shen, H. D. Zhang, C. Wu, Q. Xu, Q. H. Qi – Study on stirring behavior of liquid steel in bottom-blowing ladle with immersed cylinder (str. 601-604) |
PDF 151 KB |
|
|
| M. G. Shen, R. T. Zhang – Study on the influence of groove mold on the character of casting (str. 605-608) |
PDF 231 KB |
|
|
| P. Schlafka, A. W. Bydałek, M. Holtzer, W. Wołczyński – The influence of the ionic reactions on the refining secondary raw materials (str. 609-612) |
PDF 280 KB |
|
|
| M. Zuk, J. Gorka, A. Czuprynski, M. Adamiak – Properties and structure of the weld joints of quench and tempered 4330V steel (str. 613-616) |
PDF 375 KB |
|
|
| D. Klobčar, Tušek, M. Bizjak, S. Simončič, V. Lešer – Active flux tungsten inert gas welding of austenitic stainless steel AISI 304 (str. 617-620) |
PDF 358 KB |
|
|
| K. Skotnicová, G. S. Burkhanov, Y. S. Koshkid’ko, D. Růžička, T. Čegan, J. Cwik, N. B. Kolchugina, A. A. Lukin, O. Životský, K. Hrabovská – Influence of heat treatment on the structural and magnetic characteristics of (NdxPr1-x)2Fe14B-based magnetic material for low-temperature application (str. 621-624) |
PDF 187 KB |
|
|
| R. Mola, S. Mróz, P. Szota, S. Sawicki – The analysis of the plastic deformation of two-layered magnesium – aluminium alloys (AZ31 – Al) (str. 625-627) |
PDF 180 KB |
|
|
| S. Mróz, P. Szota, A. Stefanik – The theoretical and experimental analysis of the possibility of employing the groove rolling process for the manufacture of Mg/Al bimetallic bars (str. 628-630) |
PDF 166 KB |
|
|
| I. Jandrlić, S. Rešković, F. Vodopivec – Determining the amount of Lüders band in niobium microalloyed steel (str. 631-634) |
PDF 235 KB |
|
|
| K. Laber, H. Dyja, A. Kawałek, S. Sawicki – Determination of characteristics of plasticity of selected medium and high carbon steel grades in hot torsion test (str. 635-638) |
PDF 275 KB |
|
|
| A. Kawałek – The effect of relative deformation on the energy-force parameters in the asymmetrical plate rolling process (str. 639-642) |
PDF 165 KB |
|
|
| S. Sawicki, H. Dyja, A. Kawałek, M. Knapiński, M. Kwapisz, K. Laber – High-temperature characteristics of 20MnB4 and 30MnB4 micro-addition cold upsetting steels and C45 and C70 high-carbon-steels (str. 643-646) |
PDF 278 KB |
|
|
| R. Kruzel, M. Suliga – The impact of the heat treatment parameters on patenting line on mechanical-technological properties of steel cord wires (str. 647-650) |
PDF 174 KB |
|
|
| M. Suliga, R. Kruzel – The influence of lubricant carrier and lubrication conditions on mechanical-technological properties of high carbon steel wires (str. 651-654) |
PDF 123 KB |
|
|
| S. Rusz, I. Schindler, P. Kawulok, R. Kawulok, P. Opěla, J. Kliber, Z. Solowski – Phase transformation and cooling curves of the mild steel influenced by previous hot rolling (str. 655-658) |
PDF 251 KB |
|
|
| K. Gawdzińska, L. Chybowski, J. A. Bejger, S. Krile – Determination of technological parameters of saturated composites based on SiC by means of a model liquid (str. 659-662) |
PDF 332 KB |
|
|
D. I. Băilă, C. V. Doicin, C. M. Cotruț, M. E. Ulmeanu, I. G. Ghionea, C. I. Tarbă
– Sintering the beaks of the elevator manufactured by direct metal laser sintering (DMLS) process from Co – Cr alloy (str. 663-666) |
PDF 212 KB |
|
|
| M. Losertová, M. Štamborská, J. Lapin, V. Mareš – Comparison of deformation behavior of 316L stainless steel and Ti6Al4V alloy applied in traumatology (str. 667-670) |
PDF 365 KB |
|
|
| A. Milinović, V. Marušić, I. Samardžić – Research into boride layers growth kinetics on C45 carbon steel (str. 671-674) |
PDF 203 KB |
|
|
| V. Brozek, P. Pokorny, P. Bouska, J. Stoulil, L. Mastny – Corrosion properties of chromia based eco – friendly coatings on mild steel (str. 675-678) |
PDF 233 KB |
|
|
| M. Madej, D. Ozimina, R. Gałuszka, G. Gałuszka – Corrosion, friction and wear performance of diamond – like carbon (DLC) coatings (str. 679-682) |
PDF 222 KB |
|
|
| L. Dahil – Research on vibration damping on computer power supply box made of castermid material (str. 683-686) |
PDF 213 KB |
|
|
| J. G. He, Y. Li, X. X. Xue, H. Q. Ru, X. W. Huang, H. Yang – Cyclic voltammetry study of Ce(IV)/Ce(III) redox couple and Ce(IV)-F complex in sulfuric acid medium (str. 687-690) |
PDF 281 KB |
|
|
| V. Pepel, A. Žerovnik, R. Kunc, I. Prebil – Crack growth through low-cycle fatigue loading of material ARMOX 500T (str. 691-693) |
PDF 182 KB |
|
|
| Prethodna priopćenja |
|
|
|
| M. Jodkowski, J. Łabaj, J. Brzóska, D. Jama – Binder fraction reduction in non-ferrous metals concentrates briquetting process (str. 694-696) |
PDF 188 KB |
|
|
L. Řeháčková, R. Dudek, S. Rosypalová, D. Matýsek, J. Dobrovská
– Comprehensive study of rheological and surface properties of the selected slag system in the context of its internal structure (str. 697-700) |
PDF 133 KB |
|
|
| L. Čamek, P. Lichý, I. Kroupová, J. Duda, J. Beňo, M. Korbáš, F. Radkovský, S. Bliznyukov – Effect of cast steel production metallurgy on the emergence of casting defects (str. 701-704) |
PDF 254 KB |
|
|
| S. Medić, J. Groš, A. Horvatić, Ž. Kondić, L. Maglić – Measurement of casting parameters in ZnAlCu3 molds created by additive technology (str. 705-708) |
PDF 277 KB |
|
|
| A. Issagulov, N. Ospanov, A. Bayssanov, Ye. Makhambetov, D. Issagulova – Studying possibility of smelting refined ferromanganese grades using silicon aluminum reducer (str. 709-711) |
PDF 143 KB |
|
|
| H. Pavolová, S. Khouri, M. Cehlár, L. Domaracká, M. Puzder – Modelling of copper and zinc adsorption onto zeolite (str. 712-714) |
PDF 151 KB |
|
|
| P. V. Kovalev, S. V. Ryaboshuk, A. Z. Issagulov, V. Yu. Kulikov, Sv. S. Kvon, Y. P. Chsherbakova, G. I. Sultamurat, M. V. Jironkin – Improving production technology of tube steel grades in converter process (str. 715-718) |
PDF 137 KB |
|
|
| I. Špička, M. Heger, O. Zimný, Z. Jančíková, T. Tykva – Optimizing the model of heating the material in the reheating furnace in metallurgy (str. 719-722) |
PDF 186 KB |
|
|
| S. Gil, W. Bialik, J. Ochman – Analysis of fuel savings in metallurgical furnaces with protective atmosphere (str. 723-726) |
PDF 263 KB |
|
|
| I. Bartenev, A. Issagulov, A. Baysanov, V. Roshchin, E. Makhambetov, G. Sirgetayeva, D. Issagulovа – Studying microstructure and phase composition of a new complex calcium containing alloy (str. 727-729) |
PDF 260 KB |
|
|
| V. Marušić, I. Samardžić, I. Opačak, L. Marušić – Influence of induction hardening parameters on the GS30Mn5 weld properties (str. 730-732) |
PDF 224 KB |
|
|
| J. Kulhánek, P. Tomčík, R. Trojan, M. Juránek, P. Klaus – Experimental modeling of weld thermal cycle of the heat affected zone (HAZ)(str. 733-736) |
PDF 287 KB |
|
|
| J. Tušek, D. Klobčar – Tungsten inert gas (TIG) welding of aluminum alloy EN AW-AlZn5.5MgCu (str. 737-740) |
PDF 293 KB |
|
|
| A. Macháčková, P. Kuchta, Z. Klečková, R. Kocich, J. Szwed – Numerical simulation of the heat treatment of the weld for steam generator(str. 741-744) |
PDF 226 KB |
|
|
| B. Kalandyk, R. Zapała, J. Kasińska, B. Radoń – Impact strength of GX8CrNi12, GX5CrNi18-9 and GX5CrNiMo19-11-2 cast steel at – 30 °C (str. 745-748) |
PDF 330 KB |
|
|
| J. Kasińska – Modification influence of mischmetal on fractography fracture of G17CrMo5-5 cast steel samples after the three-point bending test (str. 749-752) |
PDF 590 KB |
|
|
| M. Mihaliková, A. Lišková – Dynamic characteristics of automotive steel sheets (str. 753-756) |
PDF 355 KB |
|
|
| J. Drápala, S. Brožová, I. Szurman, K. Konečná, G. Kostiuková, J. Vontorová, P. Jonšta, K. Sobotková – Influence of selected rare earth metals on structural characteristics of 42CrMo4 steel (str. 757-760) |
PDF 346 KB |
|
|
| I. Matin, M. Hadžistević, Đ. Vukelić, B. Trifković, M. Potran, T. Brajlih, I. Drstvenšek – Advanced procedure for fabrication of substructure in dentistry (str. 761-764) |
PDF 219 KB |
|
|
| T. Karkoszka – Factors influencing the requirements fulfilment in the zinc coating processes (str. 765-768) |
PDF 175 KB |
|
|
| A. C. Murariu, S. Crâsteţi, I. Samardzic – Detection of adherence imperfections at the inteface of substrate-coating layer by using infrared thermography (str. 769-771) |
PDF 258 KB |
|
|
| A. Gryc, T. Bajor, H. Dyja – The analysis of influence the parameters of rolling process in three high skew rolling mill of AZ31 magnesium alloy bars on temperature distribution (str. 772-774) |
PDF 236 KB |
|
|
| V. A. Andreyachshenko, M. K. Ibatov, D. A. Issagulova – Initial porosity impact on equal channel angular pressing (ECAP) of Ti–6Al–4V powder material (str. 775-778) |
PDF 186 KB |
|
|
| F. Tošenovský, D. Vykydal, P. Klaput, P. Halfarová – Stochastic optimization of laboratory test workflow at metallurgical testing centers (str. 779-782) |
PDF 185 KB |
|
|
| P. Wicher, F. Zapletal, R. Lenort, D. Staš – Measuring the metallurgical supply chain resilience using fuzzy analytic network process (str. 783-786) |
PDF 228 KB |
|
|
| A. D. Mekhtiyev, Zh. D. Zholdubayeva, B. D. Issin, E. G. Ogoltsova, A. V. Yurchenko, K. D. Issin – Method of silicon filter refining from harmful impurities (str. 787-789) |
PDF 191 KB |
|
|
| L. Blacha, J. Brzóska – The use of the balanced scorecard in evaluating the results of the innovations implemented in metallurgical companies (str. 790-792) |
PDF 187 KB |
|
|
| V. Pečínková, Z. Lenčéš, Z. Jonšta – Gass presure sintered Si3N4 – MgSiN2 composites (str. 793-795) |
PDF 198 KB |
|
|
| H. H. Yu, X. Li, Z. G. Yuan – Synthesis and characterization hollow spherical La0.7Sr0.2Ca0.1Co0.9Fe0.1O3–δ(LSCCT) for cathode of solid oxide fuel cell (SOFC) (str. 796-798) |
PDF 217 KB |
|
|
| M. Gombár, J. Kmec, M. Badida, L. Sobotová, A. Vagaská, A. Badidová – Analysis of physical factors on chosen properties of anodic alumina oxide (AAO) layers and environment (str. 799-802) |
PDF 198 KB |
|
|
| J. Całus Moszko, B. Białecka, M. Cempa-Balewicz, H. Świnder – Evaluating the possibilities of obtaining initial concentrates of rare earth elements (REEs) from fly ashes (str. 803-806) |
PDF 164 KB |
|
|
| B. Gajdzik, J. Sitko – Steel mill products analysis using qualities methods (str. 807-810) |
PDF 169 KB |
|
|
| H. Gołaś, A. Mazur, B. Mrugalska – Application of risk analysis and quality control methods for improvement of lead molding process (str. 811-814) |
PDF 300 KB |
|
|
| C. Narayanaswamy, K. Natarajan – Optimization of casting defects analysis with supply chain in cast iron foundry process (str. 815-817) |
PDF 98 KB |
|
|
| J. Korol, M. Kruczek, M. Pichlak – Material and energy flow analysis (MEFA) – first step in eco-innovation approach to assessment of steel production (str. 818-820) |
PDF 217 KB |
|
|
| A. Kujawinska, M. Rogalewicz, M. Piłacińska, A. Kochański, A. Hamrol, M. Diering – Application of dominance-based rough set approach (DRSA) for quality prediction in a casting process (str. 821-824) |
PDF 170 KB |
|
|
| S. Gil, J. Ochman, W. Bialik – A thermal study of pipes with outer transverse fins (str. 825-828) |
PDF 236 KB |
|
|
| V. A. Andreyachshenko – Finite element simulation (FES) of the fullering in device with movable elements (str. 829-831) |
PDF 120 KB |
|
|
| Pregledni radovi |
|
|
|
| R. Radić, Ž. Milošević, S. Jurić, S. Čudić – Flotation of ores and waste waters (str. 832-834) |
PDF 136 KB |
|
|
| J. Kliber – Advanced forming technology (str. 835-838) |
PDF 213 KB |
|
|
| K. Kaczmarska, B. Grabowska, D. Drożyński, A. Bobrowski, Ž. Kurleto, Ł. Szymański – Modified polysaccharides as alternative binders for foundry industry (str. 839-842) |
PDF 127 KB |
|
|
| J. Łuczak, R. Wolniak – Integration of quality, environment and safety management systems in a foundry (str. 843-845) |
PDF 120 KB |
|
|
| A. V. Todorut, L. Paliu-Popa, V. S. Tselentis, D. Cirnu – Sustainable cost reduction by lean management in metallurgical processes (str. 846-848) |
PDF 108 KB |
|
|
| D. Wilk-Kołodziejczyk, B. Mrzygłód, K. Regulski, I. Olejarczyk-Wożeńska, K. Jaśkowiec – Influence of process parameters on the properties of austempered ductile iron (ADI) examined with the use of data mining methods (str. 849-851) |
PDF 163 KB |
|
|
| L. I. Cioca, L. Ivascu – Investigating occupational diseases in the metallurgical industry (str. 852-854) |
PDF 166 KB |
|
|
| J. Machnik-Słomka, P. Kordel – Significance of technological entrepreneurship and creativity in metallurgical enterprises (str. 855-858) |
PDF 114 KB |
|
|
| A. V. Todorut, L. Paliu-Popa, D. Cirnu – Interdependence between iron ore production and maritime transport (str. 859-861) |
PDF 119 KB |
|
|
| Ostalo |
|
|
|
| Ilija Mamuzić – 13th International Symposium of Croatian Metallurgical Society »Materials and Metallurgy« – SHMD `2018, Croatia, Šibenik, June, 24 – 28, 2018 – First Circular – Call for Papers (str. 862-864) |
PDF 118 KB |
